首页 / 极空 BMS 帮助中心 / 灯板使用维护说明书 LED-5-RS485(V1.1)

灯板使用维护说明书 LED-5-RS485(V1.1)

极空官方资料全文,共约 3354 字。内容版权归成都极空科技有限公司所有,本站作为授权经销渠道整理提供,仅供参考,以厂家最新有效文件为准。

灯板使用维护说明书 Light panel Operation and maintenance manual 成都极空科技有限公司 Chengdu Jikong technology co., LTD V1.1 灯板使用维护说明书 Light panel operation and maintenance manual LED-5-RS485 成都极空科技有限公司 Chengdu Jikong technology co., LTD 灯板使用维护说明书 Light panel Operation and maintenance manual

成都极空科技有限公司 Chengdu Jikong technology co., LTD 1. 产品简介(Product Introduction) ...........................................................................................1 2. 灯板外观(Light panel appearance) .......................................................................................1

3. 接口与线缆(Interface and cables) ........................................................................................ 1 4. 接线方式(Connection diagram) .................................................................................................2

5. 灯带分布(LED strip distribution) .........................................................................................2 6. 灯用途与逻辑(Lamp Purpose and Logic) ................................................................................. 3 7. 尺寸图(Dimension drawing ) .............................................................................................. 3

灯板使用维护说明书 Light panel Operation and maintenance manual 成都极空科技有限公司 Chengdu Jikong technology co., LTD 1 1. 产品简介(Product Introduction) 本模块适用于锂电池保护板,该模块通过 RS485 协议与保护板建立通信连接,能实现 电池 SOC(荷电状态)、充电状态、放电状态等关键信息的可视化显示,为运行状态的实 时监测提供直观便捷的解决方案。 This module is suitable for lithium battery protection boards. The module establishes a

communication connection with the protection board through RS485 protocol, and can achieve visual display of key information such as battery SOC (state of charge), charging status, and discharging status, providing an intuitive and convenient solution for real-time monitoring of

operating status 2. 灯板外观(Light panel appearance) 图 1/Figure1 3. 接口与线缆(Interface and cables) 图 2-1/Figure2-1 灯板使用维护说明书 Light panel Operation and maintenance manual 成都极空科技有限公司 Chengdu Jikong technology co., LTD 2 表 1-接口定义/List1-interface definition

连接器 Connector 序号 说明 接口 1 User Interface GH1.25-6P 1 K- 2 K+ 3 GND,接地 Ground connection 4 RS485-B 5 RS485-A 6 VCC,接 12V 供电 Connect to 12V power supply 4. 接线方式(Connection diagram) 灯板提供了 1 个接口,接口 1 接保护板的显示屏接口即可,无需分辨方向。 The lamp board provides one interface, which can be connected to the display interface of

the protection board without needing to distinguish the direction. 5. 灯带分布(LED strip distribution) 表 1-灯带分布/LED strip distribution Run-Led Led-4 Led-3 Led-2 Led-1 指示灯 Operation indicator light 电量灯(Battery level light) 100% 75% 50% 25% 图 2-2/Figure2-2

灯板使用维护说明书 Light panel Operation and maintenance manual 成都极空科技有限公司 Chengdu Jikong technology co., LTD 3 6. 灯用途与逻辑(Lamp Purpose and Logic) 灯板上一共有 5 个灯,1 个按键,其中指示灯为红色,电量灯为绿色,其逻辑功能如下表 所示: 状态 指示灯 LED4 LED3 LED2 LED1 放电状态 Discharge state 闪烁 Twinkle

- - - - 充电状态 Charging status 常亮 Steady on - - - - 说明:电量灯是单独控制,只有按下按键才会点亮,并且根据保护板计算的 SOC 点亮 相对应的灯数量;放电电流大于 300mA 状态指示灯才会闪烁,充电电流大于 200mA 指示灯 常亮。 Note: The power indicator light is independently controlled and only lights up when the button is pressed. The number of lit lights corresponds to the SOC calculated by the protection

board. The status indicator will flash only when the discharge current exceeds 300mA, and the indicator will remain steady when the charging current exceeds 200mA. 7. 尺寸图(Dimension drawing) 图 3/Figure3